Switch to kernel 3.3.8(solo2)

[vuplus_openvuplus] / meta-bsp / common / recipes / linux / linux-vuplus-3.3.8 / brcm_3.3.patch

diff --git a/meta-bsp/common/recipes/linux/linux-vuplus-3.3.8/brcm_3.3.patch b/meta-bsp/common/recipes/linux/linux-vuplus-3.3.8/brcm_3.3.patch
new file mode 100644 (file)
index 0000000..f8a2371
--- /dev/null
+++ b/meta-bsp/common/recipes/linux/linux-vuplus-3.3.8/brcm_3.3.patch
@@ -0,0 +1,64 @@
+diff --git a/Makefile b/Makefile
+index 002da9a..03831b6 100644
+--- a/Makefile
++++ b/Makefile
+@@ -193,7 +193,7 @@ SUBARCH := $(shell uname -m | sed -e s/i.86/i386/ -e s/sun4u/sparc64/ \
+ # Default value for CROSS_COMPILE is not to prefix executables
+ # Note: Some architectures assign CROSS_COMPILE in their arch/*/Makefile
+ export KBUILD_BUILDHOST := $(SUBARCH)
+-ARCH          ?= $(SUBARCH)
++ARCH          ?= mips
+ CROSS_COMPILE ?= $(CONFIG_CROSS_COMPILE:"%"=%)
+ 
+ # Architecture as present in compile.h
+diff --git a/drivers/brcmstb/bchip.c b/drivers/brcmstb/bchip.c
+index b4c5b0b..4f871cd 100644
+--- a/drivers/brcmstb/bchip.c
++++ b/drivers/brcmstb/bchip.c
+@@ -450,9 +450,14 @@ void __init bchip_early_setup(void)
+               genet_pdata[0].phy_id = BRCM_PHY_ID_AUTO;
+       }
+ #else
++#if defined(CONFIG_BCMGENET_0_GPHY)
++        genet_pdata[0].phy_type = BRCM_PHY_TYPE_EXT_RGMII;
++        genet_pdata[0].phy_id = BRCM_PHY_ID_AUTO;
++#else
+       genet_pdata[0].phy_type = BRCM_PHY_TYPE_INT;
+       genet_pdata[0].phy_id = 1;
+ #endif
++#endif
+ 
+ #endif
+ 
+diff --git a/drivers/net/ethernet/broadcom/genet/Kconfig b/drivers/net/ethernet/broadcom/genet/Kconfig
+index c1ed960..8e87443 100644
+--- a/drivers/net/ethernet/broadcom/genet/Kconfig
++++ b/drivers/net/ethernet/broadcom/genet/Kconfig
+@@ -1,5 +1,27 @@
+ menu "BCMGENET options"
+ 
++config BCMGENET_0_GPHY
++        bool "GENET0 is connected to GPHY via RGMII"
++        depends on BCMGENET && BRCM_HAS_GENET_0
++        default n
++        help
++          Say Y to use an external GPHY for GENET_0.  By default this will
++          use RGMII mode and disable the internal 10/100 PHY (if present);
++          the pinmux must be set up properly in arch/mips/brcmstb/board.c .
++
++          If unsure, say N.
++
++config BCMGENET_1_GPHY
++        bool "GENET1 is connected to GPHY via RGMII"
++        depends on BCMGENET && BRCM_HAS_GENET_1
++        default n
++        help
++          Say Y to use an external GPHY for GENET_1.  By default this will
++          use RGMII mode and disable the internal 10/100 PHY (if present);
++          the pinmux must be set up properly in arch/mips/brcmstb/board.c .
++
++          If unsure, say N.
++
+ config BCMGENET_RX_DESC_THROTTLE 
+       bool "use hardware rx descriptor throttling"
+       depends on BCMGENET