X-Git-Url: http://code.vuplus.com/gitweb/?p=vuplus_dvbapp;a=blobdiff_plain;f=data%2Fsetup.xml;h=5f7cbf600cbaf51650575b41280cc76e3f83b7f3;hp=92bbc0f15acf06a8aab3c0cf46cb6fcdb224d558;hb=33a8f42447b5f3655b47f15f7c2a4cf45af5c4bb;hpb=be533a7e21618d31831e8c2ecc4898dfe5c4edcc

diff --git a/data/setup.xml b/data/setup.xml
old mode 100644
new mode 100755
index 92bbc0f..5f7cbf6
--- a/data/setup.xml
+++ b/data/setup.xml
@@ -32,8 +32,10 @@
 			<item level="1" text="Alternative radio mode">config.usage.e1like_radio_mode</item>
 			<item level="1" text="Action on long powerbutton press">config.usage.on_long_powerpress</item>
 			<item level="1" text="Action on short powerbutton press">config.usage.on_short_powerpress</item>
+			<item level="1" text="Position of finished Timers in Timerlist">config.usage.timerlist_finished_timer_position</item>
 			<item level="0" text="Infobar timeout">config.usage.infobar_timeout</item>
 			<item level="1" text="12V output" requires="12V_Output">config.usage.output_12V</item>
+			<item level="0" text="Show event-progress in channel selection">config.usage.show_event_progress_in_servicelist</item>
 			<item level="2" text="Show infobar on channel change">config.usage.show_infobar_on_zap</item>
 			<item level="2" text="Show infobar on skip forward/backward">config.usage.show_infobar_on_skip</item>
 			<item level="2" text="Show infobar on event change">config.usage.show_infobar_on_event_change</item>
@@ -46,31 +48,15 @@
 			<item level="2" text="Fast Forward speeds">config.seek.speeds_forward</item>
 			<item level="2" text="Rewind speeds">config.seek.speeds_backward</item>
 			<item level="2" text="Slow Motion speeds">config.seek.speeds_slowmotion</item>
-<!-- TRANSLATORS: Note that "Enter" in the two strings below should *not*
-     be interpreted as "Give speed as input". The intended meaning is
-     instead "Initial speed when starting winding", i.e. the speed at
-     which "winding mode" is entered when first pressing "rewind" or
-     "fast forward". -->  
-			<item level="2" text="Enter Fast Forward at speed">config.seek.enter_forward</item>
-			<item level="2" text="Enter Rewind at speed">config.seek.enter_backward</item>
-<!-- TRANSLATORS: The effect of "Non-smooth winding" is that rather
-     than using ordinary "continuous" or "smooth" winding, a fast
-     sequence of stills is shown when winding at high speeds. This
-     makes it much easier too follow when almost each frame comes from
-     a new scene. The effect is achieved by repeating each shown frame
-     a couple of times. The settings control both at which speed this
-     winding mode sets in, and how many times each frame should be
-     repeated. This was previously called "Discontinuous playback"
-     which was incomprehensible. "Non-smooth winding" may be a better
-     term, but note that there is nothing irregular about it. Synonyms
-     better suited for translation to other languages may be "stepwise
-     winding/playback", or "winding/playback using stills". -->
-			<item level="2" text="Use non-smooth winding at speeds above">config.seek.stepwise_minspeed</item>
-			<item level="2" text="Frame repeat count during non-smooth winding">config.seek.stepwise_repeat</item>
+<!-- TRANSLATORS: The following is the speed you get on the first press on fast-forward.
+     It was previously called "enter fast forward at speed" which was easily misunderstood. -->  
+			<item level="2" text="Initial Fast Forward speed">config.seek.enter_forward</item>
+			<item level="2" text="Initial Rewind speed">config.seek.enter_backward</item>
 			<item level="2" text="Behavior of 'pause' when paused">config.seek.on_pause</item>
 			<item level="2" text="Behavior of 0 key in PiP-mode">config.usage.pip_zero_button</item>
 			<item level="2" text="Alternative services tuner priority">config.usage.alternatives_priority</item>
 			<item level="2" text="Limited character set for recording filenames">config.recording.ascii_filenames</item>
+			<item level="2" text="Composition of the recording filenames">config.recording.filename_composition</item>
 		</setup>
 		<setup key="harddisk" title="Harddisk setup" >
 			<item level="0" text="Harddisk standby after">config.usage.hdd_standby</item>