+++ /dev/null
-# Kismet config file
-# Most of the "static" configs have been moved to here -- the command line
-# config was getting way too crowded and cryptic. We want functionality,
-# not continually reading --help!
-
-# Version of Kismet config
-version=2004.03.devel.a
-
-# Name of server (Purely for organiational purposes)
-servername=Kismet
-
-# User to setid to (should be your normal user)
-suiduser=your_user_here
-
-# Sources are defined as:
-# source=cardtype,interface,name[,initialchannel]
-# Card types and required drivers are listed in the README.
-# The initial channel is optional, if hopping is not enabled it can be used
-# to set the channel the interface listens on.
-source=hostap,wlan0,wlan0
-source=hostap,wlan1,wlan1
-# Other common source configs:
-# source=prism2,wlan0,prism2source
-# source=prism2_avs,wlan0,newprism2source
-# source=orinoco,eth0,orinocosource
-# An example source line with an initial channel:
-# source=orinoco,eth0,silver,11
-
-# Comma-separated list of sources to enable. This is only needed if you defined
-# multiple sources and only want to enable some of them. By default, all defined
-# sources are enabled.
-# For example:
-# enablesources=prismsource,ciscosource
-
-# Do we channelhop?
-channelhop=true
-
-# How many channels per second do we hop? (1-10)
-channelvelocity=5
-
-# By setting the dwell time for channel hopping we override the channelvelocity
-# setting above and dwell on each channel for the given number of seconds.
-#channeldwell=10
-
-# Do we split channels between cards on the same spectrum? This means if
-# multiple 802.11b capture sources are defined, they will be offset to cover
-# the most possible spectrum at a given time. This also controls splitting
-# fine-tuned sourcechannels lines which cover multiple interfaces (see below)
-channelsplit=true
-
-# Basic channel hopping control:
-# These define the channels the cards hop through for various frequency ranges
-# supported by Kismet. More finegrain control is available via the
-# "sourcechannels" configuration option.
-#
-# Don't change the IEEE80211<x> identifiers or channel hopping won't work.
-
-# Users outside the US might want to use this list:
-# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12
-defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10
-
-# 802.11g uses the same channels as 802.11b...
-defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10
-
-# 802.11a channels are non-overlapping so sequential is fine. You may want to
-# adjust the list depending on the channels your card actually supports.
-# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216
-defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64
-
-# Combo cards like Atheros use both 'a' and 'b/g' channels. Of course, you
-# can also explicitly override a given source. You can use the script
-# extras/listchan.pl to extract all the channels your card supports.
-defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64
-
-# Fine-tuning channel hopping control:
-# The sourcechannels option can be used to set the channel hopping for
-# specific interfaces, and to control what interfaces share a list of
-# channels for split hopping. This can also be used to easily lock
-# one card on a single channel while hopping with other cards.
-# Any card without a sourcechannel definition will use the standard hopping
-# list.
-# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN
-
-# ie, for us channels on the source 'prism2source' (same as normal channel
-# hopping behavior):
-# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10
-
-# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay
-# on channel 6 and prism2b to hop normally. By not setting a sourcechannels
-# line for prism2b, it will use the standard hopping.
-# sourcechannels=prism2a:6
-
-# To assign the same custom hop channel to multiple sources, or to split the
-# same custom hop channel over two sources (if splitchannels is true), list
-# them all on the same sourcechannels line:
-# sourcechannels=prism2a,prism2b,prism2c:1,6,11
-
-# Port to serve GUI data
-tcpport=2501
-# People allowed to connect, comma seperated IP addresses or network/mask
-# blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as
-# numbers (/24)
-allowedhosts=127.0.0.1
-# Maximum number of concurrent GUI's
-maxclients=5
-
-# Do we have a GPS?
-gps=true
-# Host:port that GPSD is running on. This can be localhost OR remote!
-gpshost=localhost:2947
-# Do we lock the mode? This overrides coordinates of lock "0", which will
-# generate some bad information until you get a GPS lock, but it will
-# fix problems with GPS units with broken NMEA that report lock 0
-gpsmodelock=false
-
-# Packet filtering options:
-# filter_tracker - Packets filtered from the tracker are not processed or
-# recorded in any way.
-# filter_dump - Packets filtered at the dump level are tracked, displayed,
-# and written to the csv/xml/network/etc files, but not
-# recorded in the packet dump
-# filter_export - Controls what packets influence the exported CSV, network,
-# xml, gps, etc files.
-# All filtering options take arguments containing the type of address and
-# addresses to be filtered. Valid address types are 'ANY', 'BSSID',
-# 'SOURCE', and 'DEST'. Filtering can be inverted by the use of '!' before
-# the address. For example,
-# filter_tracker=ANY(!00:00:DE:AD:BE:EF)
-# has the same effect as the previous mac_filter config file option.
-# filter_tracker=...
-# filter_dump=...
-# filter_export=...
-
-# Alerts to be reported and the throttling rates.
-# alert=name,throttle/unit,burst
-# The throttle/unit describes the number of alerts of this type that are
-# sent per time unit. Valid time units are second, minute, hour, and day.
-# Burst describes the number of alerts sent before throttling takes place.
-# For example:
-# alert=FOO,10/min,5
-# Would allow 5 alerts through before throttling is enabled, and will then
-# limit the number of alerts to 10 per minute.
-# A throttle rate of 0 disables throttling of the alert.
-# See the README for a list of alert types.
-alert=NETSTUMBLER,5/min,2
-alert=WELLENREITER,5/min,2
-alert=LUCENTTEST,5/min,2
-alert=DEAUTHFLOOD,5/min,4
-alert=BCASTDISCON,5/min,4
-alert=CHANCHANGE,5/min,4
-alert=AIRJACKSSID,5/min,2
-alert=PROBENOJOIN,5/min,2
-alert=DISASSOCTRAFFIC,5/min,2
-alert=NULLPROBERESP,5/min,5
-
-# Known WEP keys to decrypt, bssid,hexkey. This is only for networks where
-# the keys are already known, and it may impact throughput on slower hardware.
-# Multiple wepkey lines may be used for multiple BSSIDs.
-# wepkey=00:DE:AD:C0:DE:00,FEEDFACEDEADBEEF01020304050607080900
-
-# Is transmission of the keys to the client allowed? This may be a security
-# risk for some. If you disable this, you will not be able to query keys from
-# a client.
-allowkeytransmit=true
-
-# How often (in seconds) do we write all our data files (0 to disable)
-writeinterval=300
-
-# Do we use sound?
-# Not to be confused with GUI sound parameter, this controls wether or not the
-# server itself will play sound. Primarily for headless or automated systems.
-sound=false
-# Path to sound player
-soundplay=/usr/bin/play
-# Optional parameters to pass to the player
-# soundopts=--volume=.3
-# New network found
-sound_new=/usr/share/kismet/wav/new_network.wav
-# Wepped new network
-# sound_new_wep=/usr/com/kismet/wav/new_wep_network.wav
-# Network traffic sound
-sound_traffic=/usr/share/kismet/wav/traffic.wav
-# Network junk traffic found
-sound_junktraffic=/usr/share/kismet/wav/junk_traffic.wav
-# GPS lock aquired sound
-# sound_gpslock=/usr/share/kismet/wav/foo.wav
-# GPS lock lost sound
-# sound_gpslost=/usr/share/kismet/wav/bar.wav
-# Alert sound
-sound_alert=/usr/share/kismet/wav/alert.wav
-
-# Does the server have speech? (Again, not to be confused with the GUI's speech)
-speech=false
-# Server's path to Festival
-festival=/usr/bin/festival
-# How do we speak? Valid options:
-# speech Normal speech
-# nato NATO spellings (alpha, bravo, charlie)
-# spell Spell the letters out (aye, bee, sea)
-speech_type=nato
-# speech_encrypted and speech_unencrypted - Speech templates
-# Similar to the logtemplate option, this lets you customize the speech output.
-# speech_encrypted is used for an encrypted network spoken string
-# speech_unencrypted is used for an unencrypted network spoken string
-#
-# %b is replaced by the BSSID (MAC) of the network
-# %s is replaced by the SSID (name) of the network
-# %c is replaced by the CHANNEL of the network
-# %r is replaced by the MAX RATE of the network
-speech_encrypted=New network detected, s.s.i.d. %s, channel %c, network encrypted.
-speech_unencrypted=New network detected, s.s.i.d. %s, channel %c, network open.
-
-# Where do we get our manufacturer fingerprints from? Assumed to be in the
-# default config directory if an absolute path is not given.
-ap_manuf=ap_manuf
-client_manuf=client_manuf
-
-# Use metric measurements in the output?
-metric=false
-
-# Do we write waypoints for gpsdrive to load? Note: This is NOT related to
-# recent versions of GPSDrive's native support of Kismet.
-waypoints=false
-# GPSMap waypoint file. This WILL be truncated.
-waypointdata=%h/.gpsdrive/way_kismet.txt
-
-# How many alerts do we backlog for new clients? Only change this if you have
-# a -very- low memory system and need those extra bytes, or if you have a high
-# memory system and a huge number of alert conditions.
-alertbacklog=50
-
-# File types to log, comma seperated
-# dump - raw packet dump
-# network - plaintext detected networks
-# csv - plaintext detected networks in CSV format
-# xml - XML formatted network and cisco log
-# weak - weak packets (in airsnort format)
-# cisco - cisco equipment CDP broadcasts
-# gps - gps coordinates
-logtypes=dump,network,csv,xml,weak,cisco,gps
-
-# Do we track probe responses and merge probe networks into their owners?
-# This isn't always desireable, depending on the type of monitoring you're
-# trying to do.
-trackprobenets=true
-
-# Do we log "noise" packets that we can't decipher? I tend to not, since
-# they don't have anything interesting at all in them.
-noiselog=false
-
-# Do we log corrupt packets? Corrupt packets have enough header information
-# to see what they are, but someting is wrong with them that prevents us from
-# completely dissecting them. Logging these is usually not a bad idea.
-corruptlog=true
-
-# Do we log beacon packets or do we filter them out of the dumpfile
-beaconlog=true
-
-# Do we log PHY layer packets or do we filter them out of the dumpfile
-phylog=true
-
-# Do we mangle packets if we can decrypt them or if they're fuzzy-detected
-mangledatalog=true
-
-# Do we do "fuzzy" crypt detection? (byte-based detection instead of 802.11
-# frame headers)
-# valid option: Comma seperated list of card types to perform fuzzy detection
-# on, or 'all'
-fuzzycrypt=wtapfile,wlanng,wlanng_legacy,wlanng_avs,hostap,wlanng_wext
-
-# What type of dump do we generate?
-# valid option: "wiretap"
-dumptype=wiretap
-# Do we limit the size of dump logs? Sometimes ethereal can't handle big ones.
-# 0 = No limit
-# Anything else = Max number of packets to log to a single file before closing
-# and opening a new one.
-dumplimit=0
-
-# Do we write data packets to a FIFO for an external data-IDS (such as Snort)?
-# See the docs before enabling this.
-#fifo=/tmp/kismet_dump
-
-# Default log title
-logdefault=Kismet
-
-# logtemplate - Filename logging template.
-# This is, at first glance, really nasty and ugly, but you'll hardly ever
-# have to touch it so don't complain too much.
-#
-# %n is replaced by the logging instance name
-# %d is replaced by the current date as Mon-DD-YYYY
-# %D is replaced by the current date as YYYYMMDD
-# %t is replaced by the starting log time
-# %i is replaced by the increment log in the case of multiple logs
-# %l is replaced by the log type (dump, status, crypt, etc)
-# %h is replaced by the home directory
-# ie, "netlogs/%n-%d-%i.dump" called with a logging name of "Pok" could expand
-# to something like "netlogs/Pok-Dec-20-01-1.dump" for the first instance and
-# "netlogs/Pok-Dec-20-01-2.%l" for the second logfile generated.
-# %h/netlots/%n-%d-%i.dump could expand to
-# /home/foo/netlogs/Pok-Dec-20-01-2.dump
-#
-# Other possibilities: Sorting by directory
-# logtemplate=%l/%n-%d-%i
-# Would expand to, for example,
-# dump/Pok-Dec-20-01-1
-# crypt/Pok-Dec-20-01-1
-# and so on. The "dump", "crypt", etc, dirs must exist before kismet is run
-# in this case.
-logtemplate=/tmp/%n-%d-%i.%l
-
-# Where do we store the pid file of the server?
-piddir=/var/run/
-
-# Where state info, etc, is stored. You shouldnt ever need to change this.
-# This is a directory.
-configdir=%h/.kismet/
-
-# cloaked SSID file. You shouldn't ever need to change this.
-ssidmap=ssid_map
-
-# Group map file. You shouldn't ever need to change this.
-groupmap=group_map
-
-# IP range map file. You shouldn't ever need to change this.
-ipmap=ip_map
-
+++ /dev/null
-# Kismet config file
-# Most of the "static" configs have been moved to here -- the command line
-# config was getting way too crowded and cryptic. We want functionality,
-# not continually reading --help!
-
-# Version of Kismet config
-version=2004.03.devel.a
-
-# Name of server (Purely for organiational purposes)
-servername=Kismet
-
-# User to setid to (should be your normal user)
-suiduser=your_user_here
-
-# Sources are defined as:
-# source=cardtype,interface,name[,initialchannel]
-# Card types and required drivers are listed in the README.
-# The initial channel is optional, if hopping is not enabled it can be used
-# to set the channel the interface listens on.
-source=hostap,wlan0,wlan0
-source=hostap,wlan1,wlan1
-# Other common source configs:
-# source=prism2,wlan0,prism2source
-# source=prism2_avs,wlan0,newprism2source
-# source=orinoco,eth0,orinocosource
-# An example source line with an initial channel:
-# source=orinoco,eth0,silver,11
-
-# Comma-separated list of sources to enable. This is only needed if you defined
-# multiple sources and only want to enable some of them. By default, all defined
-# sources are enabled.
-# For example:
-# enablesources=prismsource,ciscosource
-
-# Do we channelhop?
-channelhop=true
-
-# How many channels per second do we hop? (1-10)
-channelvelocity=5
-
-# By setting the dwell time for channel hopping we override the channelvelocity
-# setting above and dwell on each channel for the given number of seconds.
-#channeldwell=10
-
-# Do we split channels between cards on the same spectrum? This means if
-# multiple 802.11b capture sources are defined, they will be offset to cover
-# the most possible spectrum at a given time. This also controls splitting
-# fine-tuned sourcechannels lines which cover multiple interfaces (see below)
-channelsplit=true
-
-# Basic channel hopping control:
-# These define the channels the cards hop through for various frequency ranges
-# supported by Kismet. More finegrain control is available via the
-# "sourcechannels" configuration option.
-#
-# Don't change the IEEE80211<x> identifiers or channel hopping won't work.
-
-# Users outside the US might want to use this list:
-# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12
-defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10
-
-# 802.11g uses the same channels as 802.11b...
-defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10
-
-# 802.11a channels are non-overlapping so sequential is fine. You may want to
-# adjust the list depending on the channels your card actually supports.
-# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216
-defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64
-
-# Combo cards like Atheros use both 'a' and 'b/g' channels. Of course, you
-# can also explicitly override a given source. You can use the script
-# extras/listchan.pl to extract all the channels your card supports.
-defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64
-
-# Fine-tuning channel hopping control:
-# The sourcechannels option can be used to set the channel hopping for
-# specific interfaces, and to control what interfaces share a list of
-# channels for split hopping. This can also be used to easily lock
-# one card on a single channel while hopping with other cards.
-# Any card without a sourcechannel definition will use the standard hopping
-# list.
-# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN
-
-# ie, for us channels on the source 'prism2source' (same as normal channel
-# hopping behavior):
-# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10
-
-# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay
-# on channel 6 and prism2b to hop normally. By not setting a sourcechannels
-# line for prism2b, it will use the standard hopping.
-# sourcechannels=prism2a:6
-
-# To assign the same custom hop channel to multiple sources, or to split the
-# same custom hop channel over two sources (if splitchannels is true), list
-# them all on the same sourcechannels line:
-# sourcechannels=prism2a,prism2b,prism2c:1,6,11
-
-# Port to serve GUI data
-tcpport=2501
-# People allowed to connect, comma seperated IP addresses or network/mask
-# blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as
-# numbers (/24)
-allowedhosts=127.0.0.1
-# Maximum number of concurrent GUI's
-maxclients=5
-
-# Do we have a GPS?
-gps=true
-# Host:port that GPSD is running on. This can be localhost OR remote!
-gpshost=localhost:2947
-# Do we lock the mode? This overrides coordinates of lock "0", which will
-# generate some bad information until you get a GPS lock, but it will
-# fix problems with GPS units with broken NMEA that report lock 0
-gpsmodelock=false
-
-# Packet filtering options:
-# filter_tracker - Packets filtered from the tracker are not processed or
-# recorded in any way.
-# filter_dump - Packets filtered at the dump level are tracked, displayed,
-# and written to the csv/xml/network/etc files, but not
-# recorded in the packet dump
-# filter_export - Controls what packets influence the exported CSV, network,
-# xml, gps, etc files.
-# All filtering options take arguments containing the type of address and
-# addresses to be filtered. Valid address types are 'ANY', 'BSSID',
-# 'SOURCE', and 'DEST'. Filtering can be inverted by the use of '!' before
-# the address. For example,
-# filter_tracker=ANY(!00:00:DE:AD:BE:EF)
-# has the same effect as the previous mac_filter config file option.
-# filter_tracker=...
-# filter_dump=...
-# filter_export=...
-
-# Alerts to be reported and the throttling rates.
-# alert=name,throttle/unit,burst
-# The throttle/unit describes the number of alerts of this type that are
-# sent per time unit. Valid time units are second, minute, hour, and day.
-# Burst describes the number of alerts sent before throttling takes place.
-# For example:
-# alert=FOO,10/min,5
-# Would allow 5 alerts through before throttling is enabled, and will then
-# limit the number of alerts to 10 per minute.
-# A throttle rate of 0 disables throttling of the alert.
-# See the README for a list of alert types.
-alert=NETSTUMBLER,5/min,2
-alert=WELLENREITER,5/min,2
-alert=LUCENTTEST,5/min,2
-alert=DEAUTHFLOOD,5/min,4
-alert=BCASTDISCON,5/min,4
-alert=CHANCHANGE,5/min,4
-alert=AIRJACKSSID,5/min,2
-alert=PROBENOJOIN,5/min,2
-alert=DISASSOCTRAFFIC,5/min,2
-alert=NULLPROBERESP,5/min,5
-
-# Known WEP keys to decrypt, bssid,hexkey. This is only for networks where
-# the keys are already known, and it may impact throughput on slower hardware.
-# Multiple wepkey lines may be used for multiple BSSIDs.
-# wepkey=00:DE:AD:C0:DE:00,FEEDFACEDEADBEEF01020304050607080900
-
-# Is transmission of the keys to the client allowed? This may be a security
-# risk for some. If you disable this, you will not be able to query keys from
-# a client.
-allowkeytransmit=true
-
-# How often (in seconds) do we write all our data files (0 to disable)
-writeinterval=300
-
-# Do we use sound?
-# Not to be confused with GUI sound parameter, this controls wether or not the
-# server itself will play sound. Primarily for headless or automated systems.
-sound=false
-# Path to sound player
-soundplay=/usr/bin/play
-# Optional parameters to pass to the player
-# soundopts=--volume=.3
-# New network found
-sound_new=/usr/share/kismet/wav/new_network.wav
-# Wepped new network
-# sound_new_wep=/usr/com/kismet/wav/new_wep_network.wav
-# Network traffic sound
-sound_traffic=/usr/share/kismet/wav/traffic.wav
-# Network junk traffic found
-sound_junktraffic=/usr/share/kismet/wav/junk_traffic.wav
-# GPS lock aquired sound
-# sound_gpslock=/usr/share/kismet/wav/foo.wav
-# GPS lock lost sound
-# sound_gpslost=/usr/share/kismet/wav/bar.wav
-# Alert sound
-sound_alert=/usr/share/kismet/wav/alert.wav
-
-# Does the server have speech? (Again, not to be confused with the GUI's speech)
-speech=false
-# Server's path to Festival
-festival=/usr/bin/festival
-# How do we speak? Valid options:
-# speech Normal speech
-# nato NATO spellings (alpha, bravo, charlie)
-# spell Spell the letters out (aye, bee, sea)
-speech_type=nato
-# speech_encrypted and speech_unencrypted - Speech templates
-# Similar to the logtemplate option, this lets you customize the speech output.
-# speech_encrypted is used for an encrypted network spoken string
-# speech_unencrypted is used for an unencrypted network spoken string
-#
-# %b is replaced by the BSSID (MAC) of the network
-# %s is replaced by the SSID (name) of the network
-# %c is replaced by the CHANNEL of the network
-# %r is replaced by the MAX RATE of the network
-speech_encrypted=New network detected, s.s.i.d. %s, channel %c, network encrypted.
-speech_unencrypted=New network detected, s.s.i.d. %s, channel %c, network open.
-
-# Where do we get our manufacturer fingerprints from? Assumed to be in the
-# default config directory if an absolute path is not given.
-ap_manuf=ap_manuf
-client_manuf=client_manuf
-
-# Use metric measurements in the output?
-metric=false
-
-# Do we write waypoints for gpsdrive to load? Note: This is NOT related to
-# recent versions of GPSDrive's native support of Kismet.
-waypoints=false
-# GPSMap waypoint file. This WILL be truncated.
-waypointdata=%h/.gpsdrive/way_kismet.txt
-
-# How many alerts do we backlog for new clients? Only change this if you have
-# a -very- low memory system and need those extra bytes, or if you have a high
-# memory system and a huge number of alert conditions.
-alertbacklog=50
-
-# File types to log, comma seperated
-# dump - raw packet dump
-# network - plaintext detected networks
-# csv - plaintext detected networks in CSV format
-# xml - XML formatted network and cisco log
-# weak - weak packets (in airsnort format)
-# cisco - cisco equipment CDP broadcasts
-# gps - gps coordinates
-logtypes=dump,network,csv,xml,weak,cisco,gps
-
-# Do we track probe responses and merge probe networks into their owners?
-# This isn't always desireable, depending on the type of monitoring you're
-# trying to do.
-trackprobenets=true
-
-# Do we log "noise" packets that we can't decipher? I tend to not, since
-# they don't have anything interesting at all in them.
-noiselog=false
-
-# Do we log corrupt packets? Corrupt packets have enough header information
-# to see what they are, but someting is wrong with them that prevents us from
-# completely dissecting them. Logging these is usually not a bad idea.
-corruptlog=true
-
-# Do we log beacon packets or do we filter them out of the dumpfile
-beaconlog=true
-
-# Do we log PHY layer packets or do we filter them out of the dumpfile
-phylog=true
-
-# Do we mangle packets if we can decrypt them or if they're fuzzy-detected
-mangledatalog=true
-
-# Do we do "fuzzy" crypt detection? (byte-based detection instead of 802.11
-# frame headers)
-# valid option: Comma seperated list of card types to perform fuzzy detection
-# on, or 'all'
-fuzzycrypt=wtapfile,wlanng,wlanng_legacy,wlanng_avs,hostap,wlanng_wext
-
-# What type of dump do we generate?
-# valid option: "wiretap"
-dumptype=wiretap
-# Do we limit the size of dump logs? Sometimes ethereal can't handle big ones.
-# 0 = No limit
-# Anything else = Max number of packets to log to a single file before closing
-# and opening a new one.
-dumplimit=0
-
-# Do we write data packets to a FIFO for an external data-IDS (such as Snort)?
-# See the docs before enabling this.
-#fifo=/tmp/kismet_dump
-
-# Default log title
-logdefault=Kismet
-
-# logtemplate - Filename logging template.
-# This is, at first glance, really nasty and ugly, but you'll hardly ever
-# have to touch it so don't complain too much.
-#
-# %n is replaced by the logging instance name
-# %d is replaced by the current date as Mon-DD-YYYY
-# %D is replaced by the current date as YYYYMMDD
-# %t is replaced by the starting log time
-# %i is replaced by the increment log in the case of multiple logs
-# %l is replaced by the log type (dump, status, crypt, etc)
-# %h is replaced by the home directory
-# ie, "netlogs/%n-%d-%i.dump" called with a logging name of "Pok" could expand
-# to something like "netlogs/Pok-Dec-20-01-1.dump" for the first instance and
-# "netlogs/Pok-Dec-20-01-2.%l" for the second logfile generated.
-# %h/netlots/%n-%d-%i.dump could expand to
-# /home/foo/netlogs/Pok-Dec-20-01-2.dump
-#
-# Other possibilities: Sorting by directory
-# logtemplate=%l/%n-%d-%i
-# Would expand to, for example,
-# dump/Pok-Dec-20-01-1
-# crypt/Pok-Dec-20-01-1
-# and so on. The "dump", "crypt", etc, dirs must exist before kismet is run
-# in this case.
-logtemplate=/tmp/%n-%d-%i.%l
-
-# Where do we store the pid file of the server?
-piddir=/var/run/
-
-# Where state info, etc, is stored. You shouldnt ever need to change this.
-# This is a directory.
-configdir=%h/.kismet/
-
-# cloaked SSID file. You shouldn't ever need to change this.
-ssidmap=ssid_map
-
-# Group map file. You shouldn't ever need to change this.
-groupmap=group_map
-
-# IP range map file. You shouldn't ever need to change this.
-ipmap=ip_map
-
+++ /dev/null
---- configure.o 2004-10-18 13:37:48.208863080 +0200
-+++ configure 2004-10-18 13:39:16.298471424 +0200
-@@ -5805,9 +5805,9 @@
- if test "$wireless" = "yes"; then
- # If we're compiling under linux and we need the wireless extentions,
- # then we should try to look in the current kernel module build dir, too.
-- if test "$linux" = "yes"; then
-- CPPFLAGS="$CPPFLAGS -I/lib/modules/\`uname -r\`/build/include/"
-- fi
-+ #if test "$linux" = "yes"; then
-+ # CPPFLAGS="$CPPFLAGS -I/lib/modules/\`uname -r\`/build/include/"
-+ #fi
-
- echo "$as_me:$LINENO: checking that linux/wireless.h is what we expect" >&5
- echo $ECHO_N "checking that linux/wireless.h is what we expect... $ECHO_C" >&6
+++ /dev/null
---- kismet-2004-04-R1/packet.h.orig 2005-02-04 09:12:36.000000000 +0000
-+++ kismet-2004-04-R1/packet.h 2005-02-04 09:13:14.000000000 +0000
-@@ -550,7 +550,7 @@
- // This isn't quite like STL iterators, because I'm too damned lazy to deal with all
- // the nasty STL hoop-jumping. This does provide a somewhat-stl-ish interface to
- // iterating through the singleton and masked maps
-- friend class iterator {
-+ class iterator {
- friend class macmap;
-
- public:
-@@ -643,6 +643,7 @@
- int vector_itr;
- macmap<T> *owner;
- };
-+ friend class iterator;
-
- iterator begin() {
- iterator ret(this);
+++ /dev/null
-# Kismet config file
-# Most of the "static" configs have been moved to here -- the command line
-# config was getting way too crowded and cryptic. We want functionality,
-# not continually reading --help!
-
-# Version of Kismet config
-version=2004.03.devel.a
-
-# Name of server (Purely for organiational purposes)
-servername=Kismet
-
-# User to setid to (should be your normal user)
-suiduser=your_user_here
-
-# Sources are defined as:
-# source=cardtype,interface,name[,initialchannel]
-# Card types and required drivers are listed in the README.
-# The initial channel is optional, if hopping is not enabled it can be used
-# to set the channel the interface listens on.
-source=hostap,wlan0,wlan0
-source=hostap,wlan1,wlan1
-# Other common source configs:
-# source=prism2,wlan0,prism2source
-# source=prism2_avs,wlan0,newprism2source
-# source=orinoco,eth0,orinocosource
-# An example source line with an initial channel:
-# source=orinoco,eth0,silver,11
-
-# Comma-separated list of sources to enable. This is only needed if you defined
-# multiple sources and only want to enable some of them. By default, all defined
-# sources are enabled.
-# For example:
-# enablesources=prismsource,ciscosource
-
-# Do we channelhop?
-channelhop=true
-
-# How many channels per second do we hop? (1-10)
-channelvelocity=5
-
-# By setting the dwell time for channel hopping we override the channelvelocity
-# setting above and dwell on each channel for the given number of seconds.
-#channeldwell=10
-
-# Do we split channels between cards on the same spectrum? This means if
-# multiple 802.11b capture sources are defined, they will be offset to cover
-# the most possible spectrum at a given time. This also controls splitting
-# fine-tuned sourcechannels lines which cover multiple interfaces (see below)
-channelsplit=true
-
-# Basic channel hopping control:
-# These define the channels the cards hop through for various frequency ranges
-# supported by Kismet. More finegrain control is available via the
-# "sourcechannels" configuration option.
-#
-# Don't change the IEEE80211<x> identifiers or channel hopping won't work.
-
-# Users outside the US might want to use this list:
-# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12
-defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10
-
-# 802.11g uses the same channels as 802.11b...
-defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10
-
-# 802.11a channels are non-overlapping so sequential is fine. You may want to
-# adjust the list depending on the channels your card actually supports.
-# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216
-defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64
-
-# Combo cards like Atheros use both 'a' and 'b/g' channels. Of course, you
-# can also explicitly override a given source. You can use the script
-# extras/listchan.pl to extract all the channels your card supports.
-defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64
-
-# Fine-tuning channel hopping control:
-# The sourcechannels option can be used to set the channel hopping for
-# specific interfaces, and to control what interfaces share a list of
-# channels for split hopping. This can also be used to easily lock
-# one card on a single channel while hopping with other cards.
-# Any card without a sourcechannel definition will use the standard hopping
-# list.
-# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN
-
-# ie, for us channels on the source 'prism2source' (same as normal channel
-# hopping behavior):
-# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10
-
-# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay
-# on channel 6 and prism2b to hop normally. By not setting a sourcechannels
-# line for prism2b, it will use the standard hopping.
-# sourcechannels=prism2a:6
-
-# To assign the same custom hop channel to multiple sources, or to split the
-# same custom hop channel over two sources (if splitchannels is true), list
-# them all on the same sourcechannels line:
-# sourcechannels=prism2a,prism2b,prism2c:1,6,11
-
-# Port to serve GUI data
-tcpport=2501
-# People allowed to connect, comma seperated IP addresses or network/mask
-# blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as
-# numbers (/24)
-allowedhosts=127.0.0.1
-# Maximum number of concurrent GUI's
-maxclients=5
-
-# Do we have a GPS?
-gps=true
-# Host:port that GPSD is running on. This can be localhost OR remote!
-gpshost=localhost:2947
-# Do we lock the mode? This overrides coordinates of lock "0", which will
-# generate some bad information until you get a GPS lock, but it will
-# fix problems with GPS units with broken NMEA that report lock 0
-gpsmodelock=false
-
-# Packet filtering options:
-# filter_tracker - Packets filtered from the tracker are not processed or
-# recorded in any way.
-# filter_dump - Packets filtered at the dump level are tracked, displayed,
-# and written to the csv/xml/network/etc files, but not
-# recorded in the packet dump
-# filter_export - Controls what packets influence the exported CSV, network,
-# xml, gps, etc files.
-# All filtering options take arguments containing the type of address and
-# addresses to be filtered. Valid address types are 'ANY', 'BSSID',
-# 'SOURCE', and 'DEST'. Filtering can be inverted by the use of '!' before
-# the address. For example,
-# filter_tracker=ANY(!00:00:DE:AD:BE:EF)
-# has the same effect as the previous mac_filter config file option.
-# filter_tracker=...
-# filter_dump=...
-# filter_export=...
-
-# Alerts to be reported and the throttling rates.
-# alert=name,throttle/unit,burst
-# The throttle/unit describes the number of alerts of this type that are
-# sent per time unit. Valid time units are second, minute, hour, and day.
-# Burst describes the number of alerts sent before throttling takes place.
-# For example:
-# alert=FOO,10/min,5
-# Would allow 5 alerts through before throttling is enabled, and will then
-# limit the number of alerts to 10 per minute.
-# A throttle rate of 0 disables throttling of the alert.
-# See the README for a list of alert types.
-alert=NETSTUMBLER,5/min,2
-alert=WELLENREITER,5/min,2
-alert=LUCENTTEST,5/min,2
-alert=DEAUTHFLOOD,5/min,4
-alert=BCASTDISCON,5/min,4
-alert=CHANCHANGE,5/min,4
-alert=AIRJACKSSID,5/min,2
-alert=PROBENOJOIN,5/min,2
-alert=DISASSOCTRAFFIC,5/min,2
-alert=NULLPROBERESP,5/min,5
-
-# Known WEP keys to decrypt, bssid,hexkey. This is only for networks where
-# the keys are already known, and it may impact throughput on slower hardware.
-# Multiple wepkey lines may be used for multiple BSSIDs.
-# wepkey=00:DE:AD:C0:DE:00,FEEDFACEDEADBEEF01020304050607080900
-
-# Is transmission of the keys to the client allowed? This may be a security
-# risk for some. If you disable this, you will not be able to query keys from
-# a client.
-allowkeytransmit=true
-
-# How often (in seconds) do we write all our data files (0 to disable)
-writeinterval=300
-
-# Do we use sound?
-# Not to be confused with GUI sound parameter, this controls wether or not the
-# server itself will play sound. Primarily for headless or automated systems.
-sound=false
-# Path to sound player
-soundplay=/usr/bin/play
-# Optional parameters to pass to the player
-# soundopts=--volume=.3
-# New network found
-sound_new=/usr/share/kismet/wav/new_network.wav
-# Wepped new network
-# sound_new_wep=/usr/com/kismet/wav/new_wep_network.wav
-# Network traffic sound
-sound_traffic=/usr/share/kismet/wav/traffic.wav
-# Network junk traffic found
-sound_junktraffic=/usr/share/kismet/wav/junk_traffic.wav
-# GPS lock aquired sound
-# sound_gpslock=/usr/share/kismet/wav/foo.wav
-# GPS lock lost sound
-# sound_gpslost=/usr/share/kismet/wav/bar.wav
-# Alert sound
-sound_alert=/usr/share/kismet/wav/alert.wav
-
-# Does the server have speech? (Again, not to be confused with the GUI's speech)
-speech=false
-# Server's path to Festival
-festival=/usr/bin/festival
-# How do we speak? Valid options:
-# speech Normal speech
-# nato NATO spellings (alpha, bravo, charlie)
-# spell Spell the letters out (aye, bee, sea)
-speech_type=nato
-# speech_encrypted and speech_unencrypted - Speech templates
-# Similar to the logtemplate option, this lets you customize the speech output.
-# speech_encrypted is used for an encrypted network spoken string
-# speech_unencrypted is used for an unencrypted network spoken string
-#
-# %b is replaced by the BSSID (MAC) of the network
-# %s is replaced by the SSID (name) of the network
-# %c is replaced by the CHANNEL of the network
-# %r is replaced by the MAX RATE of the network
-speech_encrypted=New network detected, s.s.i.d. %s, channel %c, network encrypted.
-speech_unencrypted=New network detected, s.s.i.d. %s, channel %c, network open.
-
-# Where do we get our manufacturer fingerprints from? Assumed to be in the
-# default config directory if an absolute path is not given.
-ap_manuf=ap_manuf
-client_manuf=client_manuf
-
-# Use metric measurements in the output?
-metric=false
-
-# Do we write waypoints for gpsdrive to load? Note: This is NOT related to
-# recent versions of GPSDrive's native support of Kismet.
-waypoints=false
-# GPSMap waypoint file. This WILL be truncated.
-waypointdata=%h/.gpsdrive/way_kismet.txt
-
-# How many alerts do we backlog for new clients? Only change this if you have
-# a -very- low memory system and need those extra bytes, or if you have a high
-# memory system and a huge number of alert conditions.
-alertbacklog=50
-
-# File types to log, comma seperated
-# dump - raw packet dump
-# network - plaintext detected networks
-# csv - plaintext detected networks in CSV format
-# xml - XML formatted network and cisco log
-# weak - weak packets (in airsnort format)
-# cisco - cisco equipment CDP broadcasts
-# gps - gps coordinates
-logtypes=dump,network,csv,xml,weak,cisco,gps
-
-# Do we track probe responses and merge probe networks into their owners?
-# This isn't always desireable, depending on the type of monitoring you're
-# trying to do.
-trackprobenets=true
-
-# Do we log "noise" packets that we can't decipher? I tend to not, since
-# they don't have anything interesting at all in them.
-noiselog=false
-
-# Do we log corrupt packets? Corrupt packets have enough header information
-# to see what they are, but someting is wrong with them that prevents us from
-# completely dissecting them. Logging these is usually not a bad idea.
-corruptlog=true
-
-# Do we log beacon packets or do we filter them out of the dumpfile
-beaconlog=true
-
-# Do we log PHY layer packets or do we filter them out of the dumpfile
-phylog=true
-
-# Do we mangle packets if we can decrypt them or if they're fuzzy-detected
-mangledatalog=true
-
-# Do we do "fuzzy" crypt detection? (byte-based detection instead of 802.11
-# frame headers)
-# valid option: Comma seperated list of card types to perform fuzzy detection
-# on, or 'all'
-fuzzycrypt=wtapfile,wlanng,wlanng_legacy,wlanng_avs,hostap,wlanng_wext
-
-# What type of dump do we generate?
-# valid option: "wiretap"
-dumptype=wiretap
-# Do we limit the size of dump logs? Sometimes ethereal can't handle big ones.
-# 0 = No limit
-# Anything else = Max number of packets to log to a single file before closing
-# and opening a new one.
-dumplimit=0
-
-# Do we write data packets to a FIFO for an external data-IDS (such as Snort)?
-# See the docs before enabling this.
-#fifo=/tmp/kismet_dump
-
-# Default log title
-logdefault=Kismet
-
-# logtemplate - Filename logging template.
-# This is, at first glance, really nasty and ugly, but you'll hardly ever
-# have to touch it so don't complain too much.
-#
-# %n is replaced by the logging instance name
-# %d is replaced by the current date as Mon-DD-YYYY
-# %D is replaced by the current date as YYYYMMDD
-# %t is replaced by the starting log time
-# %i is replaced by the increment log in the case of multiple logs
-# %l is replaced by the log type (dump, status, crypt, etc)
-# %h is replaced by the home directory
-# ie, "netlogs/%n-%d-%i.dump" called with a logging name of "Pok" could expand
-# to something like "netlogs/Pok-Dec-20-01-1.dump" for the first instance and
-# "netlogs/Pok-Dec-20-01-2.%l" for the second logfile generated.
-# %h/netlots/%n-%d-%i.dump could expand to
-# /home/foo/netlogs/Pok-Dec-20-01-2.dump
-#
-# Other possibilities: Sorting by directory
-# logtemplate=%l/%n-%d-%i
-# Would expand to, for example,
-# dump/Pok-Dec-20-01-1
-# crypt/Pok-Dec-20-01-1
-# and so on. The "dump", "crypt", etc, dirs must exist before kismet is run
-# in this case.
-logtemplate=/tmp/%n-%d-%i.%l
-
-# Where do we store the pid file of the server?
-piddir=/var/run/
-
-# Where state info, etc, is stored. You shouldnt ever need to change this.
-# This is a directory.
-configdir=%h/.kismet/
-
-# cloaked SSID file. You shouldn't ever need to change this.
-ssidmap=ssid_map
-
-# Group map file. You shouldn't ever need to change this.
-groupmap=group_map
-
-# IP range map file. You shouldn't ever need to change this.
-ipmap=ip_map
-
+++ /dev/null
-# Kismet config file
-# Most of the "static" configs have been moved to here -- the command line
-# config was getting way too crowded and cryptic. We want functionality,
-# not continually reading --help!
-
-# Version of Kismet config
-version=2004.03.devel.a
-
-# Name of server (Purely for organiational purposes)
-servername=Kismet
-
-# User to setid to (should be your normal user)
-suiduser=your_user_here
-
-# Sources are defined as:
-# source=cardtype,interface,name[,initialchannel]
-# Card types and required drivers are listed in the README.
-# The initial channel is optional, if hopping is not enabled it can be used
-# to set the channel the interface listens on.
-source=hostap,wlan0,wlan0
-source=hostap,wlan1,wlan1
-# Other common source configs:
-# source=prism2,wlan0,prism2source
-# source=prism2_avs,wlan0,newprism2source
-# source=orinoco,eth0,orinocosource
-# An example source line with an initial channel:
-# source=orinoco,eth0,silver,11
-
-# Comma-separated list of sources to enable. This is only needed if you defined
-# multiple sources and only want to enable some of them. By default, all defined
-# sources are enabled.
-# For example:
-# enablesources=prismsource,ciscosource
-
-# Do we channelhop?
-channelhop=true
-
-# How many channels per second do we hop? (1-10)
-channelvelocity=5
-
-# By setting the dwell time for channel hopping we override the channelvelocity
-# setting above and dwell on each channel for the given number of seconds.
-#channeldwell=10
-
-# Do we split channels between cards on the same spectrum? This means if
-# multiple 802.11b capture sources are defined, they will be offset to cover
-# the most possible spectrum at a given time. This also controls splitting
-# fine-tuned sourcechannels lines which cover multiple interfaces (see below)
-channelsplit=true
-
-# Basic channel hopping control:
-# These define the channels the cards hop through for various frequency ranges
-# supported by Kismet. More finegrain control is available via the
-# "sourcechannels" configuration option.
-#
-# Don't change the IEEE80211<x> identifiers or channel hopping won't work.
-
-# Users outside the US might want to use this list:
-# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12
-defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10
-
-# 802.11g uses the same channels as 802.11b...
-defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10
-
-# 802.11a channels are non-overlapping so sequential is fine. You may want to
-# adjust the list depending on the channels your card actually supports.
-# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216
-defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64
-
-# Combo cards like Atheros use both 'a' and 'b/g' channels. Of course, you
-# can also explicitly override a given source. You can use the script
-# extras/listchan.pl to extract all the channels your card supports.
-defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64
-
-# Fine-tuning channel hopping control:
-# The sourcechannels option can be used to set the channel hopping for
-# specific interfaces, and to control what interfaces share a list of
-# channels for split hopping. This can also be used to easily lock
-# one card on a single channel while hopping with other cards.
-# Any card without a sourcechannel definition will use the standard hopping
-# list.
-# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN
-
-# ie, for us channels on the source 'prism2source' (same as normal channel
-# hopping behavior):
-# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10
-
-# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay
-# on channel 6 and prism2b to hop normally. By not setting a sourcechannels
-# line for prism2b, it will use the standard hopping.
-# sourcechannels=prism2a:6
-
-# To assign the same custom hop channel to multiple sources, or to split the
-# same custom hop channel over two sources (if splitchannels is true), list
-# them all on the same sourcechannels line:
-# sourcechannels=prism2a,prism2b,prism2c:1,6,11
-
-# Port to serve GUI data
-tcpport=2501
-# People allowed to connect, comma seperated IP addresses or network/mask
-# blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as
-# numbers (/24)
-allowedhosts=127.0.0.1
-# Maximum number of concurrent GUI's
-maxclients=5
-
-# Do we have a GPS?
-gps=true
-# Host:port that GPSD is running on. This can be localhost OR remote!
-gpshost=localhost:2947
-# Do we lock the mode? This overrides coordinates of lock "0", which will
-# generate some bad information until you get a GPS lock, but it will
-# fix problems with GPS units with broken NMEA that report lock 0
-gpsmodelock=false
-
-# Packet filtering options:
-# filter_tracker - Packets filtered from the tracker are not processed or
-# recorded in any way.
-# filter_dump - Packets filtered at the dump level are tracked, displayed,
-# and written to the csv/xml/network/etc files, but not
-# recorded in the packet dump
-# filter_export - Controls what packets influence the exported CSV, network,
-# xml, gps, etc files.
-# All filtering options take arguments containing the type of address and
-# addresses to be filtered. Valid address types are 'ANY', 'BSSID',
-# 'SOURCE', and 'DEST'. Filtering can be inverted by the use of '!' before
-# the address. For example,
-# filter_tracker=ANY(!00:00:DE:AD:BE:EF)
-# has the same effect as the previous mac_filter config file option.
-# filter_tracker=...
-# filter_dump=...
-# filter_export=...
-
-# Alerts to be reported and the throttling rates.
-# alert=name,throttle/unit,burst
-# The throttle/unit describes the number of alerts of this type that are
-# sent per time unit. Valid time units are second, minute, hour, and day.
-# Burst describes the number of alerts sent before throttling takes place.
-# For example:
-# alert=FOO,10/min,5
-# Would allow 5 alerts through before throttling is enabled, and will then
-# limit the number of alerts to 10 per minute.
-# A throttle rate of 0 disables throttling of the alert.
-# See the README for a list of alert types.
-alert=NETSTUMBLER,5/min,2
-alert=WELLENREITER,5/min,2
-alert=LUCENTTEST,5/min,2
-alert=DEAUTHFLOOD,5/min,4
-alert=BCASTDISCON,5/min,4
-alert=CHANCHANGE,5/min,4
-alert=AIRJACKSSID,5/min,2
-alert=PROBENOJOIN,5/min,2
-alert=DISASSOCTRAFFIC,5/min,2
-alert=NULLPROBERESP,5/min,5
-
-# Known WEP keys to decrypt, bssid,hexkey. This is only for networks where
-# the keys are already known, and it may impact throughput on slower hardware.
-# Multiple wepkey lines may be used for multiple BSSIDs.
-# wepkey=00:DE:AD:C0:DE:00,FEEDFACEDEADBEEF01020304050607080900
-
-# Is transmission of the keys to the client allowed? This may be a security
-# risk for some. If you disable this, you will not be able to query keys from
-# a client.
-allowkeytransmit=true
-
-# How often (in seconds) do we write all our data files (0 to disable)
-writeinterval=300
-
-# Do we use sound?
-# Not to be confused with GUI sound parameter, this controls wether or not the
-# server itself will play sound. Primarily for headless or automated systems.
-sound=false
-# Path to sound player
-soundplay=/usr/bin/play
-# Optional parameters to pass to the player
-# soundopts=--volume=.3
-# New network found
-sound_new=/usr/share/kismet/wav/new_network.wav
-# Wepped new network
-# sound_new_wep=/usr/com/kismet/wav/new_wep_network.wav
-# Network traffic sound
-sound_traffic=/usr/share/kismet/wav/traffic.wav
-# Network junk traffic found
-sound_junktraffic=/usr/share/kismet/wav/junk_traffic.wav
-# GPS lock aquired sound
-# sound_gpslock=/usr/share/kismet/wav/foo.wav
-# GPS lock lost sound
-# sound_gpslost=/usr/share/kismet/wav/bar.wav
-# Alert sound
-sound_alert=/usr/share/kismet/wav/alert.wav
-
-# Does the server have speech? (Again, not to be confused with the GUI's speech)
-speech=false
-# Server's path to Festival
-festival=/usr/bin/festival
-# How do we speak? Valid options:
-# speech Normal speech
-# nato NATO spellings (alpha, bravo, charlie)
-# spell Spell the letters out (aye, bee, sea)
-speech_type=nato
-# speech_encrypted and speech_unencrypted - Speech templates
-# Similar to the logtemplate option, this lets you customize the speech output.
-# speech_encrypted is used for an encrypted network spoken string
-# speech_unencrypted is used for an unencrypted network spoken string
-#
-# %b is replaced by the BSSID (MAC) of the network
-# %s is replaced by the SSID (name) of the network
-# %c is replaced by the CHANNEL of the network
-# %r is replaced by the MAX RATE of the network
-speech_encrypted=New network detected, s.s.i.d. %s, channel %c, network encrypted.
-speech_unencrypted=New network detected, s.s.i.d. %s, channel %c, network open.
-
-# Where do we get our manufacturer fingerprints from? Assumed to be in the
-# default config directory if an absolute path is not given.
-ap_manuf=ap_manuf
-client_manuf=client_manuf
-
-# Use metric measurements in the output?
-metric=false
-
-# Do we write waypoints for gpsdrive to load? Note: This is NOT related to
-# recent versions of GPSDrive's native support of Kismet.
-waypoints=false
-# GPSMap waypoint file. This WILL be truncated.
-waypointdata=%h/.gpsdrive/way_kismet.txt
-
-# How many alerts do we backlog for new clients? Only change this if you have
-# a -very- low memory system and need those extra bytes, or if you have a high
-# memory system and a huge number of alert conditions.
-alertbacklog=50
-
-# File types to log, comma seperated
-# dump - raw packet dump
-# network - plaintext detected networks
-# csv - plaintext detected networks in CSV format
-# xml - XML formatted network and cisco log
-# weak - weak packets (in airsnort format)
-# cisco - cisco equipment CDP broadcasts
-# gps - gps coordinates
-logtypes=dump,network,csv,xml,weak,cisco,gps
-
-# Do we track probe responses and merge probe networks into their owners?
-# This isn't always desireable, depending on the type of monitoring you're
-# trying to do.
-trackprobenets=true
-
-# Do we log "noise" packets that we can't decipher? I tend to not, since
-# they don't have anything interesting at all in them.
-noiselog=false
-
-# Do we log corrupt packets? Corrupt packets have enough header information
-# to see what they are, but someting is wrong with them that prevents us from
-# completely dissecting them. Logging these is usually not a bad idea.
-corruptlog=true
-
-# Do we log beacon packets or do we filter them out of the dumpfile
-beaconlog=true
-
-# Do we log PHY layer packets or do we filter them out of the dumpfile
-phylog=true
-
-# Do we mangle packets if we can decrypt them or if they're fuzzy-detected
-mangledatalog=true
-
-# Do we do "fuzzy" crypt detection? (byte-based detection instead of 802.11
-# frame headers)
-# valid option: Comma seperated list of card types to perform fuzzy detection
-# on, or 'all'
-fuzzycrypt=wtapfile,wlanng,wlanng_legacy,wlanng_avs,hostap,wlanng_wext
-
-# What type of dump do we generate?
-# valid option: "wiretap"
-dumptype=wiretap
-# Do we limit the size of dump logs? Sometimes ethereal can't handle big ones.
-# 0 = No limit
-# Anything else = Max number of packets to log to a single file before closing
-# and opening a new one.
-dumplimit=0
-
-# Do we write data packets to a FIFO for an external data-IDS (such as Snort)?
-# See the docs before enabling this.
-#fifo=/tmp/kismet_dump
-
-# Default log title
-logdefault=Kismet
-
-# logtemplate - Filename logging template.
-# This is, at first glance, really nasty and ugly, but you'll hardly ever
-# have to touch it so don't complain too much.
-#
-# %n is replaced by the logging instance name
-# %d is replaced by the current date as Mon-DD-YYYY
-# %D is replaced by the current date as YYYYMMDD
-# %t is replaced by the starting log time
-# %i is replaced by the increment log in the case of multiple logs
-# %l is replaced by the log type (dump, status, crypt, etc)
-# %h is replaced by the home directory
-# ie, "netlogs/%n-%d-%i.dump" called with a logging name of "Pok" could expand
-# to something like "netlogs/Pok-Dec-20-01-1.dump" for the first instance and
-# "netlogs/Pok-Dec-20-01-2.%l" for the second logfile generated.
-# %h/netlots/%n-%d-%i.dump could expand to
-# /home/foo/netlogs/Pok-Dec-20-01-2.dump
-#
-# Other possibilities: Sorting by directory
-# logtemplate=%l/%n-%d-%i
-# Would expand to, for example,
-# dump/Pok-Dec-20-01-1
-# crypt/Pok-Dec-20-01-1
-# and so on. The "dump", "crypt", etc, dirs must exist before kismet is run
-# in this case.
-logtemplate=/tmp/%n-%d-%i.%l
-
-# Where do we store the pid file of the server?
-piddir=/var/run/
-
-# Where state info, etc, is stored. You shouldnt ever need to change this.
-# This is a directory.
-configdir=%h/.kismet/
-
-# cloaked SSID file. You shouldn't ever need to change this.
-ssidmap=ssid_map
-
-# Group map file. You shouldn't ever need to change this.
-groupmap=group_map
-
-# IP range map file. You shouldn't ever need to change this.
-ipmap=ip_map
-
+++ /dev/null
---- configure.orig 2005-02-21 12:12:23.061566024 +0000
-+++ configure 2005-02-21 12:12:34.560817872 +0000
-@@ -6225,9 +6225,9 @@
- if test "$wireless" = "yes"; then
- # If we're compiling under linux and we need the wireless extentions,
- # then we should try to look in the current kernel module build dir, too.
-- if test "$linux" = "yes"; then
-- CPPFLAGS="$CPPFLAGS -I/lib/modules/$(uname -r)/build/include/"
-- fi
-+ #if test "$linux" = "yes"; then
-+ # CPPFLAGS="$CPPFLAGS -I/lib/modules/$(uname -r)/build/include/"
-+ #fi
-
- echo "$as_me:$LINENO: checking that linux/wireless.h is what we expect" >&5
- echo $ECHO_N "checking that linux/wireless.h is what we expect... $ECHO_C" >&6
+++ /dev/null
-SECTION = "console/network"
-DESCRIPTION = "Kismet is an 802.11 layer2 wireless network detector, sniffer, and intrusion detection system"
-HOMEPAGE = "http://www.kismetwireless.net/"
-LICENSE = "GPLv2"
-DEPENDS = "expat gmp"
-
-SRC_URI = "http://www.kismetwireless.net/code/kismet-2004-04-R1.tar.gz \
- file://no-strip.diff;patch=1;pnum=0 \
- file://no-chmod.diff;patch=1;pnum=0 \
- file://no-lib-modules-uname-include.diff;patch=1;pnum=0 \
- file://packet_friend_fix.patch;patch=1 \
- file://glibc3.3.2-getopt-throw.diff;patch=1;pnum=0"
-
-SRC_URI_append_mtx-1 = " file://kismet.conf"
-SRC_URI_append_mtx-2 = " file://kismet.conf"
-
-EXTRA_OECONF = "--with-pcap=linux --disable-setuid"
-
-inherit autotools
-
-do_configure() {
- unset CFLAGS CPPFLAGS
- oe_runconf
-}
-
-do_install_append() {
- if test -e ${WORKDIR}/kismet.conf; then
- install -m 644 ${WORKDIR}/kismet.conf ${D}${sysconfdir}/
- fi
-}
-
-PACKAGES =+ "kismet-sounds"
-FILES_kismet-sounds = "${datadir}/kismet/wav"
-
-CONFFILES_${PN}_nylon = "${sysconfdir}/kismet.conf"
+++ /dev/null
-SECTION = "console/network"
-DESCRIPTION = "Kismet is an 802.11 layer2 wireless network detector, sniffer, and intrusion detection system"
-HOMEPAGE = "http://www.kismetwireless.net/"
-LICENSE = "GPLv2"
-DEPENDS = "expat gmp"
-
-SRC_URI = "http://www.kismetwireless.net/code/kismet-2005-01-R1.tar.gz \
- file://no-strip.diff;patch=1;pnum=0 \
- file://no-chmod.diff;patch=1;pnum=0 \
- file://no-lib-modules-uname-include.diff;patch=1;pnum=0 \
- file://glibc3.3.2-getopt-throw.diff;patch=1;pnum=0"
-
-
-EXTRA_OECONF = "--with-pcap=linux --disable-setuid"
-
-inherit autotools
-
-do_configure() {
- oe_runconf
-}
-
-
-do_install_append() {
- if test -e ${WORKDIR}/kismet.conf; then
- install -m 644 ${WORKDIR}/kismet.conf ${D}${sysconfdir}/
- fi
-}
-
-PACKAGES =+ "kismet-sounds"
-FILES_kismet-sounds = "/usr/share/kismet/wav"
-
-CONFFILES_${PN}_nylon = "${sysconfdir}/kismet.conf"
projects / vuplus_openembedded / commitdiff